精品欧美乱码久久久久久,久艹天天日天天干天天爽,一木道中文免费二区欧美专区,亚州av大香蕉

銷售咨詢熱線
15953126901
15153196527
公司新聞 hengye
企業案例 case

聯系我們

  • 聯系人:濟南燕翔鐵藝制品有限公司
  • 手機:15953126901
  • 電話:15153196527
  • 郵箱:785385551@qq.com
  • 地址:濟南市天橋區歷山北路黃臺不銹鋼市場3區317
當前位置: 首頁 > 新聞資訊>公司新聞

鐵藝大門的焊接工藝

來源:http://m.eastagcn.com.cn 日期:2024-06-06 發布人: 瀏覽次數:1

1.邊框焊接  按邊框尺寸在地上定位。將邊框料的兩端寬邊上切成45。對接后點焊。校正無誤<方框的對角線要相等)后焊牢。

1. The border welding is positioned on the ground according to the border size. Cut the two wide edges of the border material into 45 pieces. Spot welding after docking. After correction, ensure that the diagonals of the boxes are equal and weld them firmly.

2.中間長豎管焊接  每扇門3根長豎管,均勻分布在邊框內,定位間距為339毫米。擺放好位置后,先點焊,再校平,檢查無誤后再焊牢。

2. Weld 3 long vertical pipes in the middle of each door, evenly distributed within the frame, with a positioning spacing of 339 millimeters. After placing the position, spot weld first, then level and check for accuracy before welding firmly.

3.矛頭用橫管焊接每扇門4根,夾在中問長豎竹之間、擺放好位置后,先點焊,再校平,檢查無誤后再焊牢:

3. Weld 4 horizontal pipes to each door with the spearhead, clamp them between the long vertical bamboo in the middle, place them in the right position, spot weld first, then level and check for accuracy before welding firmly:

20231024065223409.jpg

4.中間短豎管焊接  侮扇門4根.按圖樣中的位置擺好。先點焊,再校平,檢查無誤后再焊牢。

4. Weld 4 short vertical pipes in the middle and place them according to the positions in the drawing. First spot weld, then level, check for accuracy, and then weld firmly.

5.最短橫管焊接每扇門24根.按圖樣中的位置擺好。先點焊,再校平,檢查無誤后再焊牢。為防l上焊接變形,可問隔焊。由于順序打亂,焊點較多,焊完后應檢查有無漏焊部位。

5. Weld 24 pieces of the shortest horizontal pipe for each door. Arrange them according to the position in the drawing. First spot weld, then level, check for accuracy, and then weld firmly. To prevent welding deformation, it is possible to ask for insulation welding. Due to the disorder of the order and the presence of many welding points, it is necessary to check for any missing areas after welding.

6.槍頭焊接依次將各槍頭分別焊在相應的位置上.要求與橫桿垂直,正面朝前,不能扭曲。

6. Weld each gun head in the corresponding position in sequence. It is required to be perpendicular to the horizontal bar, facing forward, and not twisted.

7.花形焊接把所有花形分別擺放在相應位置上,看是否合適,調整無誤后,先點焊到框架上,整體再檢查一遍,然后焊牢。

7. Flower welding: Place all flower shapes in their respective positions, check if they are suitable, adjust them correctly, first spot weld them to the frame, check the whole again, and then weld them firmly.

日日噜噜噜噜久久久| 激情亚洲无码一区二区三区| 国产一区在线性感| 美一区二区三区| 超碰 日本人| aaa中文字幕久久久| 欧美黄色日婷婷| 三级在线第一页| 婷婷 久久久| 日韩肛奸少妇视频| 人妻女医av谷原希美| 国产 日韩 欧美 在线观看| 欧美人妻专区3| 亚洲最新AV一区二区三区| 午夜福利在线观看免费不卡视屏| ***综合狠狠综合区| 校园春色另类人妻| 黄色AV可以看的| 欧美日韩中文制服人妻在线| 超碰在线caoporn婷婷| 欧美3级日韩3级国产3级| 午夜视频在线观看| 午夜主播一区| 婷婷六月七月在线| 自拍第一页一区二区三区| 小视频嗯嗯嗯| Www.色国产.com| 骚妇草逼喷水视频| 草B片奂费看| 亚洲无码精品第二页在线观看 | 国模偷拍综合网| 射丝脚一区二区| 亚洲 欧美 日韩 不卡| 人妻三级在线| 国产老阿姨免费| 无码加勒比| 日本人妻字幕久久久| 少妇AV网站大全| 日日躁夜夜躁人人躁| 国产精品三级影片| 啊~操我~唔~啊啊好爽~视频|