卷簾門遙控器的配對方法因類型不同而有所差異，以下是常見的幾種配對方式：

The pairing methods for remote control of rolling shutter doors vary depending on the type. The following are common pairing methods:

學習型遙控器配對

Pairing of Learning Remote Control

準備工作：確保卷簾門電源已開啟且處于待機狀態，檢查遙控器電池電量充足，確認遙控器與卷簾門型號匹配。

Preparation: Ensure that the power supply of the rolling shutter door is turned on and in standby mode, check that the remote control battery is fully charged, and confirm that the remote control matches the rolling shutter door model.

進入控制器學習模式：使用螺絲刀打開卷簾門控制器的外殼，找到主板上的學習按鈕（通常標記為 “Learn” 或 “學習”）。按下并保持該按鈕幾秒鐘，直到指示燈開始閃爍，表示控制器進入學習模式，部分控制器通過按下學習按鈕后會發出聲音提示進入學習模式。

Enter controller learning mode: Use a screwdriver to open the housing of the rolling shutter door controller and locate the learning button on the motherboard (usually labeled as "Learn" or "Learn"). Press and hold the button for a few seconds until the indicator light starts flashing, indicating that the controller has entered learning mode. Some controllers will emit a sound prompt to enter learning mode by pressing the learning button.

同步遙控器：在控制器處于學習模式時，按下遙控器上的任意按鍵（通常是開門鍵），等待幾秒鐘，確?？刂破髯R別遙控器信號。

Synchronous remote control: When the controller is in learning mode, press any button on the remote control (usually the door open button) and wait for a few seconds to ensure that the controller recognizes the remote control signal.

完成配對：指示燈停止閃爍或發出確認聲，表示配對成功。

Pairing completed: The indicator light stops flashing or makes a confirmation sound, indicating successful pairing.

測試：關閉控制器外殼，按下遙控器上的按鍵測試卷簾門的開啟和關閉功能。

Test: Close the controller casing and press the button on the remote control to test the opening and closing function of the rolling shutter door.

撥碼型遙控器配對

Dial type remote control pairing

清碼：卷簾門遙控器接收模塊上面一般有一個白色或者黑色的按鍵，即學習鍵。在通電的情況下，按下這個學習鍵，此時學習鍵旁的學習指示燈亮起，等它閃兩下熄滅之后，松開手，清碼成功。

Clear code: There is usually a white or black button on the receiving module of the rolling shutter door remote control, which is the learning button. When powered on, press this learning button. The learning indicator light next to the learning button will light up. After it flashes twice and goes out, release your hand and clear the code successfully.

對碼：清碼成功后，再次按下學習鍵，此時學習指示燈亮起，然后按下手柄上面的按鍵，此時學習指示燈會閃 5 下，接著熄滅，表明卷簾門遙控器對碼成功。

Code pairing: After successfully clearing the code, press the learning button again, and the learning indicator light will turn on. Then press the button on the handle, and the learning indicator light will flash 5 times and then turn off, indicating that the remote control for the rolling shutter door has successfully aligned the code.

對拷型遙控器配對

Pairing of Copy type Remote Control

清碼：一般是雙手同時按遙控器鎖鍵和下行鍵，這時指示燈會不停閃動，再松開雙手。然后隨便按一個鍵，遙控器指示燈亮一下就熄滅，表示清碼成功。

Clear code: Generally, both hands press the lock button and down button on the remote control at the same time. At this time, the indicator light will flash continuously, and then release both hands. Then press any key and the remote control indicator light will turn on and then turn off, indicating successful code clearing.

對拷：拿出需要配對的新遙控器與原遙控器，兩個遙控器對準，雙手同時按住兩個遙控器的開門鍵，指示燈快速閃動即為成功。

Copy: Take out the new remote control that needs to be paired with the original remote control, align the two remote controls, hold down the door opening buttons of both remote controls with both hands, and the indicator light flashes quickly to indicate success.

其他按鍵拷貝：其他按鍵如關門鍵、停止鍵、鎖鍵等的拷貝方法與開門鍵相同，依次進行即可。

Copy other buttons: The copying method for other buttons such as the door close button, stop button, lock button, etc. is the same as that for the door open button, and can be done sequentially.

智能 App 配對

Intelligent App Matching

下載應用程序：根據卷簾門的品牌，在手機應用商店下載相應的手機應用程序。

Download the application: Depending on the brand of the rolling shutter door, download the corresponding mobile application from the mobile app store.

注冊并登錄賬號：打開應用程序，按照提示進行用戶注冊并登錄。

Register and log in account: Open the application, fol