鐵藝大門類型多種多樣.風格各異，而且莊重、豪華。顏色也可以選擇自己喜歡的。有的用戶會擔心表面會生銹，其實完全沒必要擔心，看看下面對于鐵藝大門表面處理的工序，你就知道鐵藝大門是耐用的、防銹的：

There are various types of wrought iron gates Different styles, and solemn and luxurious. You can also choose the color you like. Some users may worry about rusting on the surface, but there is no need to worry at all. Take a look at the surface treatment process for wrought iron doors below, and you will know that wrought iron doors are durable and rust proof:

一、清除工序，就是清除焊渣 鐵藝大門的焊接部位較多，必須認真清除每個焊接部位的焊渣。先用板銼或扁鐵敲打除渣，然后用磨光機和砂布打磨焊縫，使其平滑。對飛濺到其他部位的焊渣也要順勢清除干凈。

1、 The cleaning process is to remove welding slag from the welding parts of the iron gate, and it is necessary to carefully remove the welding slag from each welding part. First, use a board file or flat iron to remove slag, and then use a polishing machine and sandpaper to polish the weld seam to make it smooth. The welding slag that splashes onto other parts should also be cleaned up in a timely manner.

二、加固工序，涂抹原子灰 用原子灰加固化劑(比例50:1)攪拌均勻，涂抹在焊接部位，處理焊縫缺陷。

2、 The reinforcement process involves applying atomic ash with a curing agent (50:1 ratio) and stirring evenly. The mixture is then applied to the welding area to address any defects in the weld seam.

三、打磨工序，打磨原子灰 干透后，用磨光機和砂布全面打磨大門的各個組件，尤其是涂抹原子灰的部位更要磨光。

3、 The polishing process involves using a polishing machine and sanding cloth to thoroughly polish all components of the gate after the atomic ash has dried, especially the areas coated with atomic ash.

四、噴涂工序，鐵藝大門在噴漆 噴漆前，用濕布全面擦凈鐵藝大門的各個部位，不能留有灰塵等。然后第一道給鐵藝大門噴防銹漆，干透再噴一遍，干透還要再噴一遍，漆膜干透后噴三遍自己喜歡的漆，最后噴一道清漆。注意不能有漏噴部位，也不能產生流掛等缺陷。個別細微處可用刷子刷涂補漆。

4、 Spray painting process: Before painting the iron gate, use a damp cloth to thoroughly wipe all parts of the iron gate without leaving any dust or debris. Then spray the first layer of rust proof paint on the wrought iron gate, spray it again when it dries, and spray it again when it dries. After the paint film dries, spray it three times with your favorite paint, and finally spray a clear coat. Be careful not to have any areas of leakage or defects such as sagging. Individual small details can be brushed and repainted with a brush.